ALL Ikelite products referenced, are on preorder; contact/email us for $ & shipping availability!

 PN: # 71704 

Canon EOS 7D DSLR UNDERWATER HOUSING

ABOUT THIS PRODUCT

A full featured and durable waterproof housing for Canon EOS 7D DSLR cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water.

This housing requires the addition of a compatible DL Lens Port for waterproof operation. Lens Port not included.

Introduced in 2013, the Canon EOS 7D has an 18MP CMOS sensor with good autofocus capabilities and low-light performance. The APS-C crop sensor is great underwater for both close-up work with either a 60mm or 100mm Macro lens and wide angle with the fantastic Tokina 10-17mm Fisheye.

Legacy Four Lock Port Compatibility

Due to differences in mount diameter and zoom engagement, DL and FL system ports cannot be used interchangeably. The DL port mount may be removed using a T15 Torx bit and replaced with old style Port Locks for FL Port System (Set of 4) # 5509.04 for legacy users with standard or modular ports from our Four Lock system. This modification will prevent the use of newer DL ports. Re-installation of the DL port base will require the housing to be returned to Ikelite or an Authorized Dealer and may incur additional service charges. The housing cannot be converted back and forth repeatedly.

There are significant advantages to upgrading your lens ports which you can read about here. If you're shooting an 8" diameter dome, you'll also save almost 2 pounds by switching to the DL version. Contact us for more information about Trade-Up opportunities.

Vacuum System

The included vacuum valve allows you to pressurize the housing to check for leaks prior to putting your expensive equipment in the water. Use of the vacuum valve requires a compatible Vacuum Pump with Gauge # 47011, sold separately.

There is no greater assurance than being able to see your camera and o-ring seal through the back of the housing. Our signature open-groove design suspends the rear o-ring in a natural position that is easier to maintain and more reliable than forcing the o-ring into a channel. Once the housing is closed you can see the o-ring form a solid, waterproof seal.

Controls and Set-Up

Shutter and AF-ON levers stand out with super sensitive and natural feeling curved levers.  Both controls can be extended using the optional Shutter Trigger Extension # 4077.93 for more comfortable use when using a right-hand quick release handle.

All push button controls are machined and hard anodized aluminum to reduce weight and resist salt build-up. The back of the housing is laser engraved with control symbols which will never fade or fall off.

The camera mount is front-loading for easy installation and removal. A small mounting plate attaches to the bottom of the camera and secures in the front of the housing. The camera mounting plate does not need to be removed from the camera for surface use or when changing the battery or memory cards. The mounting plate features a 1/4-20 threaded mount on the bottom so that it can be attached to a tripod on the surface.

Handling & Travel

The housing, tray, and handles have been optimized to reduce weight while maintaining strength and durability. The Right-Hand Quick Release Handle # 4077.02 (sold separately) can be added or removed depending on your needs. The precision machined aluminum base features 1/4-20 tripod mounting sockets and additional mounting locations for future accessories. The base and handle can be quickly removed when breaking down your system for travel.

A 1/4-20 threaded mounting point is located front and center on the housing above the lens port mount. This mount can be used to attach lightweight accessories like a focus light or GoPro camera.

If you're shooting with two strobe or lighting arms, then a top handle can be added to carry to and from the dive site. Top handles are available in a Cable Grip # 4080.07 or Aluminum Top Handle # 4080.08. The rigid aluminum version provides additional mounting points for lighting and accessories.

Construction

Our new ABS-PC blend front is stronger than its clear counterpart, provides improved contrast and visibility, and keeps your camera running cooler in the sun.

Every housing is made in the USA, individually inspected for fit, and water pressure tested to 200 feet (60m).

Compatibility

This housing is only compatible with Canon EOS 7D camera as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories. 

Differences in lens and control placement prevent other DSLR models, including the newer EOS 7D Mark II, from being used in this housing. We are not aware of any other models which may be used in or adapted to this particular housing.

 

Specifications

  • 200' (60m) depth rating

  • Compatible with DL system lens ports

  • Controls are provided for all important camera controls; Controls are not provided for LCD panel illumination button, Depth-of-field preview button, Dioptric adjustment knob, Multi-function (M-Fn) button, Quick Control Dial switch, Lens lock pin, and Multi-controller 

  • 1/4-20 thread base mounts with 3.5" spacing

  • Near neutral buoyancy in fresh water

  • Actual buoyancy varies depending on choice of lens and port

  • 4.8 lb (2.2 kg)

  • 9.2 x 7.1 x 6.6" (234 x 180 x 168 mm)

  • Vacuum valve included (pump sold separately)

  • Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes

  • ABS-PC construction is fundamentally corrosion-resistant

  • Made in the USA; Individually inspected for fit and water pressure tested to depth

  • 1 year limited warranty

 PN: # 71015 

NIKON D850 DSLR UNDERWATER HOUSING

A full featured and durable waterproof housing for Nikon D850 DSLR cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water.

This housing requires the addition of a compatible DL Lens Port for waterproof operation. Lens Port not included.

Features

This popular model has been redesigned from the ground up to include all of our latest improvements.

Lens Ports

The single most important feature is our long awaited new Dry Lock (DL) port system. This exciting new system is even more robust and even easier to assemble than our time-tested Four Lock (FL) system. The new ports are lighter and more adaptable, and can accommodate extremely large diameter lenses with ease. If you're considering shooting professional quality lenses like the Nikon 14-24mm or Sigma 10-20mm HSM, then the DL system is essential.

Most popular zoom lenses and select lens focus rings can be engaged using a simple yet effective gearing system that puts adjustment right at your fingertips. A large, soft-touch lobed knob on the side of the housing makes fine tuned adjustments a breeze. Zoom and focus gears differ depending on which lens you are using. All are lightweight and affordable. Refer to the DL System Port Chart to choose the correct gear. Zoom gears sold separately.

Due to differences in mount diameter and zoom engagement, DL and FL system ports cannot be used interchangeably. The DL port mount may be removed and replaced with old style Port Locks for FL Port System (Set of 4) # 5509.04 for legacy users with standard or modular ports from our Four Lock system. This modification will prevent the use of newer DL ports. The housing cannot be converted back and forth repeatedly. Re-installation of the DL port base will require the housing to be returned to Ikelite or an Authorized Dealer and may incur additional service charges. There are significant advantages to upgrading your lens ports which you can read about here. If you're shooting an 8" diameter dome, you'll also save almost 2 pounds by using the DL version instead.

Vacuum System

The included vacuum valve allows you to vacuum test the housing to check for leaks prior to putting your expensive equipment in the water. Combined with a full view of the camera and o-ring seal through the back of the housing, there is no greater assurance that your gear will be safe. Our signature open-groove design suspends the rear o-ring in a natural position that is easier to maintain and more reliable than forcing the o-ring into a channel. Use of the vacuum valve requires a compatible Vacuum Pump with Gauge # 47011, sold separately.

Construction

Our new white ABS-PC blend front is stronger than its clear counterpart, provides improved contrast and visibility, and keeps your camera running cooler in the sun.

Like its predecessor and all of our housings, this product is made in the USA, individually inspected for fit, and water pressure tested to 200 feet (60m).

Compatibility

This housing is only compatible with the Nikon D750 DSLR as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.

Differences in lens and control placement prevent other DSLR models from being used in this housing. We are not aware of any other models which may be used in or adapted to this particular housing.

 

Specifications

  • 200' (60m) depth rating

  • Compatible with DL system lens ports

  • Controls are provided for all important camera controls; Controls are not provided for Release mode dial, Release mode dial lock release, Diopter adjustment control, Focus mode selector, PV button, Fn1 button, Eyepiece shutter lever, Sub selector, Focus selector lock

  • 1/4-20 thread base mounts with 3.5" spacing

  • Near neutral buoyancy in fresh water

  • Actual buoyancy varies depending on choice of lens and port

  • 4.9 lb (2.2 kg)

  • 9.1 x 7 x 6.5" (231 x 178 x 165 mm)

  • Vacuum valve included (pump sold separately)

  • Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes

  • ABS-PC and Lexan construction is fundamentally corrosion-resistant

  • Made in the USA; Individually inspected for fit and water pressure tested to depth

  • 1 year limited warranty

 

In the Box

  • Housing

  • Rear o-ring # 0132.61

  • Front o-ring # 0132.45

  • Base with Left-Hand Quick Release Handle # 4077.67

  • Port Hole Cover # 0200.92

  • Zoom Gear Retainer # 75900

  • Tool for Zoom Gear Retainer # 0945.06

  • Waterproof Bulkhead Cap # 9104.5

  • 4-40 Hex Key # 0945.11

  • 1/16" Hex Key # 0945.16

  • 1/8" Hex Key # 0945.18

  • Control + Push Button Tip Assortment # 9249

  • Silicone Lubricant 1cc Tube # 0184.2

 PN: # 71702

CANON EOS 5D 5D Mark III, 5D Mark IV, 5DS, 5DS R DSLR UNDERWATER HOUSING

A full featured and durable waterproof housing for Canon EOS 5D Mark III, 5D Mark IV, 5DS, and 5DS R DSLR cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water.

This housing requires the addition of a compatible DL Lens Port for waterproof operation. Lens Port not included.

Key Features

  • 200' (60m) depth rating

  • Housing back is interchangeable with optional lightweight 50' (15m) back (sold separately); the 50' back is lighter weight for travel and perfect for snorkeling, surf, and pool work

  • Perfect for any wet environment including surf, dive, and pool use

  • Supremely functional for maximum creative control—access is provided for all important camera functions

  • The new Dry Lock (DL) Port System gives added security at the surface of the water and accommodates large diameter lenses

  • Extra-large, soft touch zoom knob; Zoom is accessible for many lenses using our unique universal zoom gear system

  • Vacuum valve included; Test your system after assembly prior to entering the water; Pump sold separately

  • Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL circuitry provides automatic exposure with compatible Ikelite DS strobes

  • Control symbols are laser etched into the back and will never fade or rub off

  • Quick install camera mount plate does not need to be removed for battery or memory card access

  • One spare 1/2-20 threaded accessory port locations on the front of the housing for the addition of optional accessories

  • Includes a balanced aluminum base with left-hand quick release handle; Right-hand handle sold separately.

  • Signature open-groove design suspends the rear o-ring in a natural position that is easier to maintain and more reliable than forcing the o-ring into a channel

  • ABS-PC and Lexan construction is fundamentally corrosion-resistant

  • Made in the USA; Individually inspected for fit and water pressure tested to depth

  • 1 year limited warranty

Compatibility

This housing is only compatible with cameras as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.

Differences in lens and control placement prevent other DSLR models from being used in this housing. We are not aware of any other models which may be used in or adapted to this particular housing.

Specifications

  • 200' (60m) depth rating

  • Compatible with DL system lens ports

  • 1/4-20 thread base mounts with 3.5" spacing

  • Near neutral buoyancy in fresh water

  • Actual buoyancy varies depending on choice of lens and port

  • 5.1 lb (2.3 kg)

  • 9.2 x 7.1 x 6.5" (234 x 180 x 165 mm)

 

In the Box

  • Housing

  • Rear O-ring # 0132.61

  • Front O-ring # 0132.45

  • Base with Left-Hand Quick Release Handle # 4077.67

  • Port Hole Cover # 0200.92

  • Zoom Gear Retainer # 75900

  • Waterproof Bulkhead Cap # 9104.5

  • Silicone Lubricant # 0184.2

  • Control + Pushbutton Tip Assortment # 9249

  • 1/16" Hex Key # 0945.16

  • 1/8" Hex Key # 0945.18

  • 1 year limited warranty

 PN: # 71007 

NIKON D750 DSLR UNDERWATER HOUSING

A full featured and durable waterproof housing for Nikon D750 DSLR cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water.

This housing requires the addition of a compatible DL Lens Port for waterproof operation. Lens Port not included.

Features

This popular model has been redesigned from the ground up to include all of our latest improvements.

Lens Ports

The single most important feature is our long awaited new Dry Lock (DL) port system. This exciting new system is even more robust and even easier to assemble than our time-tested Four Lock (FL) system. The new ports are lighter and more adaptable, and can accommodate extremely large diameter lenses with ease. If you're considering shooting professional quality lenses like the Nikon 14-24mm or Sigma 10-20mm HSM, then the DL system is essential.

Most popular zoom lenses and select lens focus rings can be engaged using a simple yet effective gearing system that puts adjustment right at your fingertips. A large, soft-touch lobed knob on the side of the housing makes fine tuned adjustments a breeze. Zoom and focus gears differ depending on which lens you are using. All are lightweight and affordable. Refer to the DL System Port Chart to choose the correct gear. Zoom gears sold separately.

Vacuum System

The included vacuum valve allows you to vacuum test the housing to check for leaks prior to putting your expensive equipment in the water. Combined with a full view of the camera and o-ring seal through the back of the housing, there is no greater assurance that your gear will be safe. Our signature open-groove design suspends the rear o-ring in a natural position that is easier to maintain and more reliable than forcing the o-ring into a channel. Use of the vacuum valve requires a compatible Vacuum Pump with Gauge # 47011, sold separately.

Controls and Set-Up

We've upgraded the shutter and AF-ON levers to a more natural feeling curved design. Both controls can optionally be extended using the Shutter Trigger Extension # 4077.93 for more comfortable use when using a right-hand quick release handle. If you're not already using back button focus, we recommend learning this valuable trick.

Our push buttons have been redesigned to reduce weight and salt build-up. The back of the housing features laser engraved control symbols which will never fade or fall off.

The camera mount is now front-loading for easy installation and removal. A small mounting plate attaches to the bottom of the camera and secures in the front of the housing. The camera mounting plate does not need to be removed from the camera for surface use or when changing the battery or memory cards. The mounting plate features a 1/4-20 threaded mount on the bottom so that it can be attached to a tripod on the surface.

Construction

Our new white ABS-PC blend front is stronger than its clear counterpart, provides improved contrast and visibility, and keeps your camera running cooler in the sun.

Like its predecessor and all of our housings, this product is made in the USA, individually inspected for fit, and water pressure tested to 200 feet (60m).

Compatibility

This housing is only compatible with the Nikon D750 DSLR as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.

Differences in lens and control placement prevent other DSLR models from being used in this housing. We are not aware of any other models which may be used in or adapted to this particular housing.

 

Specifications

  • 200' (60m) depth rating

  • Compatible with DL system lens ports

  • Controls are provided for all important camera controls; Controls are not provided for Release mode dial, Release mode dial lock release, Diopter adjustment control, Focus mode selector, Focus selector lock, PV button, Fn button, BKT button

  • 1/4-20 thread base mounts with 3.5" spacing

  • Near neutral buoyancy in fresh water

  • Actual buoyancy varies depending on choice of lens and port

  • 4.8 lb (2.2 kg)

  • 9.2 x 7.2 x 6.5" (234 x 183 x 168 mm)

  • Vacuum valve included (pump sold separately)

  • Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes

  • ABS-PC and Lexan construction is fundamentally corrosion-resistant

  • Made in the USA; Individually inspected for fit and water pressure tested to depth

  • 1 year limited warranty

 

In the Box

  • Housing

  • Rear o-ring # 0132.61

  • Front o-ring # 0132.45

  • Base with Left-Hand Quick Release Handle # 4077.67

  • Port Hole Cover # 0200.92

  • Zoom Gear Retainer # 75900

  • Tool for Zoom Gear Retainer # 0945.06

  • Waterproof Bulkhead Cap # 9104.5

  • 4-40 Hex Key # 0945.11

  • 1/16" Hex Key # 0945.16

  • 1/8" Hex Key # 0945.18

  • Control + Push Button Tip Assortment # 9249

  • Silicone Lubricant 1cc Tube # 0184.2

+65 6336 6186

114 Lavender Street, CT HUB2, #05-52 (Lift Lobby 3)

Singapore 338729

OPENING HOURS/DAYS :

Mondays and/or Public Holiday(s): CLOSED

 

Tuesdays – Fridays : 11.00am to 7.00pm

(Meal break closure@ 2:30pm - 3:30pm)

 

Saturdays : 11.00am to 5.00pm

 

Sundays : By Appointments basis ONLY

For your convenience and ease, please visit us at least half an hour before closing time.

©2018 by ScubaCam. Proudly created with Wix.com